NZFF

by **Snowman** » Sun Mar 16, 2008 3:54 pm

Just uploaded to Avsim,............. Hawera Airfield, NZHA.
See link below for details........................

http://nzff.org/forum/viewtopic.php?t=6194

Lawrie. >nzflag<

by **SteelBlades** » Sun Mar 16, 2008 7:36 pm

Bonza!

by **Bazza** » Mon Mar 17, 2008 10:04 am

Thanks again Lawrie, the gaps are slowly being filled.

One question........... :rolleyes:

On taking off at Hawera, I discovered an unfortunate effect that I have previously noticed in the Coromandel scenes where there is a boundary fence.

I find that if the runway is short, I am having a "building crash" effect when clearing the fence by approximately 2 to 3 metres. Obviously this also happens when trying to land short by coming in low over the end boundary fence. Obviously I can solve the problem by removing the fence but at the moment it is somewhat un-realistic. Is there any fix for this effect ?

If needed I could supply a "screenie" but this would only show my Cessna stopped in mid air, some metres above the fence. :wub:

tks Bazza.

by **Snowman** » Mon Mar 17, 2008 3:48 pm

Bazza wrote:
QUOTE (Bazza @ Mar 17 2008, 11:04 AM) <{POST_SNAPBACK}>
Thanks again Lawrie, the gaps are slowly being filled.

One question...........

On taking off at Hawera, I discovered an unfortunate effect that I have previously noticed in the Coromandel scenes where there is a boundary fence.

I find that if the runway is short, I am having a "building crash" effect when clearing the fence by approximately 2 to 3 metres. Obviously this also happens when trying to land short by coming in low over the end boundary fence. Obviously I can solve the problem by removing the fence but at the moment it is somewhat un-realistic. Is there any fix for this effect ?

If needed I could supply a "screenie" but this would only show my Cessna stopped in mid air, some metres above the fence.

tks Bazza.

Offhand, i would have to say no,...i cant really think of any "fix" to this, other than turning OFF crash detection.
Strange,.............. i havnt had this happen,........... might have to investigate a little more,..................

Lawrie. >nzflag<

by **Bazza** » Mon Mar 17, 2008 4:21 pm

I should have thought of removing the crash mode. Have done this now and it solves the problem, doesn't seem "right and proper" though.

When I experienced this "fence crash I was using a secondary runway, not the main one.

I just tried using the main "load up" runway to check the fences, but before I could get to them......ooops, look what happened. :arrr:

I'll go and look in those nice sheds you provided and see if you've left a chainsaw in there..... :lol:

by **Bazza** » Thu Mar 27, 2008 8:37 am

Has anyone else got these trees or is it just me ?

by **Snowman** » Thu Mar 27, 2008 10:20 am

Bazza wrote:
QUOTE (Bazza @ Mar 27 2008, 09:37 AM) <{POST_SNAPBACK}>
Has anyone else got these trees or is it just me ?

Try copying and pasting the following exclude line to the bottom of Hawera's entry in the main FS9 scenery.cfg file.......

Exclude=S39 32.91,E174 15.88,S39 33.01,E174 16.02,objects

Dont forget to SAVE it before you exit the cfg file !!

I made this exclude using pure guesswork, just going by the location of the trees in your pic.
I dont have the trees there in my sim...................

Lawrie. >nzflag<

by **Bazza** » Fri Mar 28, 2008 8:55 am

Nice one Lawrie, trees all gone, just in case someone else has the same drama.

Thanks. :clap:

by **Snowman** » Fri Mar 28, 2008 1:15 pm

Bazza wrote:
QUOTE (Bazza @ Mar 28 2008, 09:55 AM) <{POST_SNAPBACK}>
Nice one Lawrie, trees all gone, just in case someone else has the same drama.

Thanks.

Sweet as,............... just happy it fixed your problem,..........

Lawrie.

NZFF

Hawera NZHA

Who is online